跳至主要内容

Transformer radiator / corrugated fins welding machine

full automatic transformer oil tank radiator corrugated fins welding machine
The machine is driven by the reducer drive chain for horizontal movement of the corrugated fins, automatic stop, automatic continuous welding corrugated fins, corrugated fins using pneumatic clamping ,welding servo motor driven ball screw up and down vertical movement, the width and height of the corrugated fins are set an the touch screen. The operation is simple and easy to understand. The welded corrugated fins have good appearance, smooth surface.
Model
A400-1300
Sizes（L，W，H）
4160*2200*2380mm
Motor power
1.5KW*2
Pressure adjust range
0.2-0.8MPA
corrugated fin Min. welding width
300mm
corrugated fin Max. Welding width
1300mm
corrugated fin welding height
50mm-400mm
steel thickness
1.0-1.6mm
space between fins
45mm-80mm
welding speed
2-4fins/min.
welding performance
smooth surface
weight
3000KG

--pneumatic parts：
SC80*50  standard cylinder
SC63*75  standard cylinder
1.5" hydraulic filter
4V210-08/DC24V  HANBING
AFC 2000   Filter、Silencer
a. Adjust electric current slow increase & decrease, welding process be controlled effectively.
b. Equipped with pulse welding function, pulse frequency division high frequency / low frequency.
c. Has perfect undervoltage, overvoltage and overcurrent protection,  and is safe and reliable.
d. Welding station rotation, circular welding operation, vertical welding seam.
e. The workpiece is clamped by the fixture .
f.  Machine has high voltage, slow arc ignition function, reliable arc ignition and low voltage arc suppression.
g. The welding gun can be adjusted horizontally, and it can be used to weld various specifications corrugated fins.
CONTROL PANEL PLC touch screen.jpg
a. PLC Touch screen：Mitsubishi
（PLC touch screen has automatic & manual control method. Automatic control can be set parameters of fins quantity, fins height, space between fins directly）
b. DS2-20P7-BS( 3M brake wire) : XINJIE servo motor
c. DS2-20P7-BS(5M brake wire) : XINJIE servo motor
d.  3steps knob，2steps knob ，emergency stop button，green button，pilot lamp：all use CHNT brand
e.  relay， switching ， air switch： Schneider
f. PR18-8DN 24VDC   delivery and insertion probe : OMRON
g. PR18-8DN 24VDC  mobile box exit limit probe :OMRON
h. SN04-N 24VDC  Am limiting probe: OMRON
i.  Infrared sensor：AUTONICS
j. NMRV090-60-YEJ1.5KW   brake motor（reducer）
k. NMRV090-100-Y1.5KW  motor（reducer）


标签：

评论

发表评论

此博客中的热门博文

Tapping failure reasons analysis

After the first metal part be tapped, we always to check it: if pass the thread gauge inspection? The inspection result is OK, we can do mass production. If it fails, We should consider which reasons cause tapping faiulre. KYLT provide Metal Machining services for:  WEDM, EDM, DRILL, TAPPING ,  CNC LATHING ,  CNC MILLING ,  ALUMINUM / MAGNESIUM / PLASTIC RAPID PROTOTYPES MAKING . 1PCS ORDER IS ALLOWED. Aluminum CNC machined workpiece Normally, the following reasons may cause screw thread faiulre: 1) UNQUALIFIED TAP Tap is wear or bad 2) QUALIFIED DRILLING HOLE (BEFORE TAPPING) If the hole is too small, because of friction, will increase the difficulty of tapping, while tapping faster wear, and vice versa, the hole is too big, it can easily tap into, but the quality of teeth is very poor, because the diameter of teeth will become larger, relative to the screw nut bonding force is insufficient, easy to slide teeth. In M3 *0.5, the correct hole (general...
发表评论
阅读全文

CNC MACHINE BE CLASSIFIED BY SERVO CONTROL MODE

Servo control mode to classify CNC machine tool. (1) open loop control CNC machine tool The feed servo drive of this kind of machine tool is open-loop, that is, there is no detection feedback device. Generally, its driving motor is a stepping motor. The main feature of stepping motor is that every time the control circuit changes the command pulse signal, the motor will rotate a step angle, and the motor itself has self-locking ability. The drive circuit is controlled by the pulse distributor, which controls the coordinate displacement by changing the number of pulses, the displacement speed by changing the frequency of pulses, and the direction of displacement by changing the distribution sequence of pulses. Therefore, this control mode is characterized by convenient control, simple structure and low price. The command signal flow from the CNC system is unidirectional, so there is no stability problem of the control system, but because the error of the mechanical transmission...
发表评论
阅读全文

SELECTION PRINCIPLE OF CUTTING PARAMETERS FOR SCREW THREAD TURNING

Because the pitch (or lead) of the thread is specified by the drawing, the key to choose the cutting parameters when  turning  the screw thread is to determine the spindle speed n and the cutting depth AP. 1) SELECTION OF SPINDLE SPEED TO DO SCREW THREAD TURNING According to the mechanism that the spindle turns 1 and the cutter feeds 1 lead when turning the thread, the feed speed of the CNC lathe is determined by the selected spindle speed. The thread lead (which is the pitch when the thread is single head thread) instructed in the thread processing program section is equivalent to the feed speed VF VF = n f (1) expressed by the feed rate f (mm / R) From Formula 1, it can be seen that the feed speed VF is proportional to the feed amount F. if the spindle speed of the machine tool is selected too high, the converted feed speed will greatly exceed the rated feed speed of the machine tool. Therefore, when selecting the rotation speed of the main shaft for turning the threa...
发表评论
阅读全文